Build / Roofing / Sponsors / Timelapse / Tiny House Resources / Tips

Roofing

roof: (noun)
The structure forming the upper covering of a building or vehicle… or both!!!

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

We’ve been struggling to find the right roofing material for our Tiny House. Conventional asphalt shingles aren’t very attractive or wind resistant; wood shingles and shakes are heavy and require care; ceramic tiles and slates are expensive and heavy; thatching will burn your house down; and finally, asbestos will give you cancer. Great…

So what’s left? Metal roofing? This seems to be the go-to material for Tiny Houses out there. It’s readily available, comes in a variety of colors, is durable, wind resistant, and recyclable. But it’s fairly expensive, has to be protected from corrosion, can be difficult to install and could interfere with cellular reception!

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

This is where Ondura came in and introduced us to their new Onduvilla 3D Shingles Roofing System. The shingles are made with at least 50% recycled fibers (paper, cardboard and receipts) and impregnated with asphalt. The materials are lighter than the competition, more affordable, and just as durable. And since the asphalt is impregnated throughout the shingle, you don’t really have to worry about scratches as you would with metal (something to consider if you plan on towing your house through low clearance tree branches).

The design of the shingles also makes them high-wind resistant. The ribs overlap and create a rigid and tight bond.

Soon after we hung up with Ondura, we received a pallet of materials. Installation was a breeze! We snapped a horizontal chalk line on top of your roof underlayment to place the first row of shingles. From there, the other rows just line up. Like everything else that needs to resist rain, we started from the bottom and worked our way up. Since we plan on towing the house all over the country, we also had to consider wind. So we also had to make sure that the shingles overlapped from the back of the trailer to the front.

Here are a few other things we learned from roofing our house.

Sheathing:

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

We used 1/2″ plywood for your roof sheathing. It’s thick enough to hold the Onduvilla ring shank nails in place and is significantly lighter than 3/4″ plywood.

Underlayment:

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

We used Grace Ice & Water Shield for our underlayment and highly recommend it. It’s fairly expensive but worth it.

Roof ends:

This is the part where we didn’t plan to well. We should’ve laid our shingles on the roof before securing them and figure out how much overhang we’d have on each end.

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

We didn’t do that and therefore our roof ends were difficult to button-up. Do as we say, not as we do! We placed the rib of our first shingle flush with the end of our roof and the last piece just ended up wherever it ended up! The end cap fit nicely over the rib of the first shingle since it was flush, as seen below.

But it wouldn’t on the other side. We used a heat-gun to heat up the shingles and bend them without breaking them. Then we screwed a piece of 2×2 redwood onto our sheathing to create a fake rib. We heated up the shingles again, folded them back onto the piece of lumber and finally added the end cap.

Ridge:

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

We used the “apron” pieces at the top, then some flashing and the ridge cap. Again, working our way up, and back to front.

Dormers:

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

We applied flashing to our wall/roof transition under the house wrap, then added a piece of metal flashing. We marked where to bend the flashing and hammered it into shape on the edge of a big metal work bench.

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

For the eaves under the dormers, we installed thin pieces strips of shingles and used the same aprons as with the ridge. We also used flashing under the house wrap and onto the apron.

 Skylights:

For the skylights we were able to use the flashing provided by Fakro and installed the shingles over it.

Additional tips:

  • We used an oscillating tool to cut the excess shingle material off the roof edges. A sharp utility knife works too.
  • We were generous with roofing cement in the areas prone to water infiltration.
  • Our table saw worked great to cut the shingles to size, but the blade got coated with asphalt, and so did I!
  • Metal snips are very useful for cutting details.
  • It is safe to walk on the roof but we have to be careful not to step onto the ribs as they could crack.
  • When we hammered the nails onto the top of each rib, we made sure that the rubber washer was snug but not crushed. The washer shouldn’t spin freely, but we should be able to move it with a bit of force.

As you might have read recently, we took our house for test drive and the shingles resisted highway speeds without a problem!

We love our new roof. Not only do the shingles look great, but they are also light, easy to work with, durable, made of recycled materials and built to compliment the Tiny House lifestyle.

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

Roofing

Read more: www.tinyhousegiantjourney.com
Follow us: www.facebook.com/tinyhousegiantjourney

Thank you Roy for helping us with the installation!

-Guillaume (safe and dry)

You can find all the information about Onduvilla 3D Shingles here: http://ondura.com/our-products/onduvilla/

—————–

Find out how you can become a sponsor here!

—————–

Music by: I Am Machi. Thank you for the tunes!
Check out more of their music here: http://www.iammachi.com/
Friend them on Facebook here: http://www.facebook.com/machiloveshappy

About these ads

6 thoughts on “Roofing

  1. Pingback: Three Things to Consider Before Opting for a Metal Roof | Ondura

  2. Pingback: Shakes & Roof Tiles | PapaGreyBeard's Almost Tiny House Project

  3. Pingback: Ondura Partnering with Big Players in Tiny House Movement | Ondura

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s